Gorb, Stanislav N.
Lade...
Preferred name
Gorb, Stanislav N.
Official Name
Gorb, Stanislav N.
Alternative Name
Gorb, Stanislav
Gorb, S. N.
Email
sgorb@zoologie.uni-kiel.de
ORCID
GND
5 Ergebnisse
Einstellungen
Gerade angezeigt 1 - 5 von 5
- Some of the metrics are blocked by yourconsent settings
Item-typ:Veröffentlichung, Investigating the efficiency of a bio-inspired insect repellent surface structure(Institut of Physics, 2018); ; ; ; Most insects with smooth or hairy adhesive pads have very little problems in attaching to smooth substrates. A careful selection of surface roughness, however, can effectively limit the contact area of the adhesive organs with the surface. In comparison to conventional toxin-based insect repelling methods, biologically inspired micro- and nanostructured insect repellent surface structures, thus, offer a great potential to effective and environmentally-friendly control insect pests. We here present a simple experimental approach to qualitatively and quantitatively analyse the efficiency of a micro- and nanorough surface structure. Nauphoeta cinerea and Gastrophysa viridula as model organisms for insects with smooth and hairy adhesive pads, respectively, were placed in an enclosed environment. The escape movements of freely running insects over either the repellent or a control surfaces were counted and analyzed in detail. The tested surface structures were able to significantly reduce the escape of cockroaches with smooth adhesive pads by 44.1%. Interestingly, the data indicates that N. cinerea might use mechanical cues from the antenna to discriminate between surfaces before making contact with the adhesive pads. G. viridula with hairy adhesive pads were not significantly affected by the surface structure. By carefully adjusting 'critical' surface topography parameters relevant for insect adhesion, more efficient and selective repellent surfaces might be achieved. Such nanostructure-based insect repellent surfaces could also help to utilize recruitment behavior of certain insect species and might present a novel approach to effectively control insect pests.Wissenschaftlicher ArtikelBand:13Heft:5121 - Some of the metrics are blocked by yourconsent settings
Item-typ:Veröffentlichung, Insect wing damage: causes, consequences and compensatory mechanismsThe evolution of wings has played a key role in the success of insect species, allowing them to diversify to fill many niches. Insect wings are complex multifunctional structures, which not only have to withstand aerodynamic forces but also need to resist excessive stresses caused by accidental collisions. This Commentary provides a summary of the literature on damage-reducing morphological adaptations in wings, covering natural causes of wing collisions, their impact on the structural integrity of wings and associated consequences for both insect flight performance and life expectancy. Data from the literature and our own observations suggest that insects have evolved strategies that (i) reduce the likelihood of wing damage and (ii) allow them to cope with damage when it occurs: damage-related fractures are minimized because wings evolved to be damage tolerant and, in the case of wing damage, insects compensate for the reduced aerodynamic efficiency with dedicated changes in flight kinematics.Wissenschaftlicher ArtikelBand:223Heft:9138 - Some of the metrics are blocked by yourconsent settings
Item-typ:Veröffentlichung, Effect of microstructure on the mechanical and damping behaviour of dragonfly wing veins(Royal science publication, 2016-02); ; ; ; Insect wing veins are biological composites of chitin and protein arranged in a complex lamellar configuration. Although these hierarchical structures are found in many 'venous wings' of insects, very little is known about their physical and mechanical characteristics. For the first time, we carried out a systematic comparative study to gain a better understanding of the influence of microstructure on the mechanical characteristics and damping behaviour of the veins. Morphological data have been used to develop a series of three-dimensional numerical models with different material properties and geometries. Finite-element analysis has been employed to simulate the mechanical response of the models under different loading conditions. The modelling strategy used in this study enabled us to determine the effects selectively induced by resilin, friction between layers, shape of the cross section, material composition and layered structure on the stiffness and damping characteristics of wing veins. Numerical simulations suggest that although the presence of the resilin-dominated endocuticle layer results in a much higher flexibility of wing veins, the dumbbell-shaped cross section increases their bending rigidity. Our study further shows that the rubber-like cuticle, friction between layers and material gradient-based design contribute to the higher damping capacity of veins. The results of this study can serve as a reference for the design of novel bioinspired composite structures.Wissenschaftlicher ArtikelBand:3Heft:2144 - Some of the metrics are blocked by yourconsent settings
Item-typ:Veröffentlichung, Hydrofoil-like legs help stream mayfly larvae to stay on the ground(Springer, 2023-03); ; ; ; Adaptations to flow have already been in the focus of early stream research, but till today morphological adaptations of stream insects are hardly understood. While most previous stream research focused on drag, the effects of lift on ground-living stream insects have been often overlooked. Stream mayfly larvae Ecdyonurus sp. graze on algae on top of the stones and therefore inhabit current exposed places in streams. They have a dorso-ventrally flattened body shape, which is known to reduce drag. However, this body shape enhances lift too, increasing the danger for the animal of getting detached from the substrate. Using microscopic techniques, 3D-printing, and drag and lift measurements in a wind tunnel, our experiments show that the widened femora of Ecdyonurus sp. can generate negative lift, contributing to counterbalance the (positive) lift of the overall body shape. The larvae can actively regulate the amount of lift by adjusting the femur's tilt or optimizing the distance to the ground. This shows that morphological adaptations of benthic stream insects can be very elaborate and can reach far beyond adaptations of the overall body shape. In the presented case, Ecdyonurus sp. takes advantage of the flow to overcome the flow's challenges.Wissenschaftlicher ArtikelBand:20989 - Some of the metrics are blocked by yourconsent settings
Item-typ:Veröffentlichung, Stiffness distribution in insect cuticle: a continuous or a discontinuous profile?(Royal Society of Chemistry, 2017); ; ; ; Insect cuticle is a biological composite with a high degree of complexity in terms of both architecture and material composition. Given the complex morphology of many insect body parts, finite-element (FE) models play an important role in the analysis and interpretation of biomechanical measurements, taken by either macroscopic or nanoscopic techniques. Many previous studies show that the interpretation of nanoindentation measurements of this layered composite material is very challenging. To develop accurate FE models, it is of particular interest to understand more about the variations in the stiffness through the thickness of the cuticle. Considering the difficulties of making direct measurements, in this study, we use the FE method to analyse previously published data and address this issue numerically. For this purpose, sets of continuous or discontinuous stiffness profiles through the thickness of the cuticle were mathematically described. The obtained profiles were assigned to models developed based on the cuticle of three insect species with different geometries and layer configurations. The models were then used to simulate the mechanical behaviour of insect cuticles subjected to nanoindentation experiments. Our results show that FE models with discontinuous exponential stiffness gradients along their thickness were able to predict the stress and deformation states in insect cuticle very well. Our results further suggest that, for more accurate measurements and interpretation of nanoindentation test data, the ratio of the indentation depth to cuticle thickness should be limited to 7% rather than the traditional '10% rule'. The results of this study thus might be useful to provide a deeper insight into the biomechanical consequences of the distinct material distribution in insect cuticle and also to form a basis for more realistic modelling of this complex natural composite.Wissenschaftlicher ArtikelBand:14Heft:132146